Skip to content

Filter syntax

Filters limit the set of features affected by a rule's properties. There are several types of simple filters, which can be combined to provide more complex filters for rules.

Combining filters

Combination is done in the usual CSS way. A rule with two filters separated by a comma affects any features that match either filter, while a rule with two filters separated by only whitespace affects only features that match both filters. Here's an example using a basic attribute filter (described below):

/* Matches places where the lake is flooding */
[rainfall>12] [lakes>1] {
    fill: black;
}

/* Matches wet places */
[rainfall>12], [lakes>1] {
    fill: blue;
}

When writing a selector that uses both and and or combinators, remember that the and combinator has higher precedence. For example:

restricted [cat='2'], [cat='3'], [cat='4'] [@sd <= 200k] [@sd > 100k] {
  fill: #EE0000;
}

The above selector should be read as:

  • typename is 'restricted' and cat='2' or
  • cat='3' or
  • cat='4' and scale is between 100000 and 200000

If instead the intention was to combine in or just the three cat filters, the right syntax would have been:

restricted [cat='2' or cat='3' or cat='4'] [@sd <= 200k] [@sd > 100k] {
  fill: #EE0000;
}

Which should be read as:

  • typename is 'restricted' and
  • (cat='2' or cat='3' or cat='4') and
  • scale is between 100000 and 200000

Filtering on data attributes

An attribute filter matches some attribute of the data (for example, a column in a database table). This is probably the most common type of filter. An attribute filter takes the form of an attribute name and a data value separated by some predicate operator (such as the less-than operator <).

Supported predicate operators include the following:

Operator Meaning
= The property must be exactly equal to the specified value.
<> The property must not be exactly equal to the specified value.
> The property must be greater than (or alphabetically later than) the specified value.
>= The property must be greater than or equal to the specified value.
< The property must be less than (or alphabetically earlier than) the specified value.
<= The property must be less than or equal to the specified value.
LIKE The property must match the pattern described by the specified value. Patterns use _ to indicate a single unspecified character and % to indicate an unknown number of unspecified characters.

For example, to only render outlines for the states whose names start with letters in the first half of the alphabet, the rule would look like:

[STATE_NAME<='M'] {
    stroke: black;
}

Note

The current implementation of property filters uses ECQL syntax, described on the GeoTools documentation.

Filtering on type

When dealing with data from multiple sources, it may be useful to provide rules that only affect one of those sources. This is done very simply; just specify the name of the layer as a filter:

states {
    stroke: black;
}

Filtering by ID

For layers that provide feature-level identifiers, you can style specific features simply by specifying the ID. This is done by prefixing the ID with a hash sign (#):

#states.2 {
    stroke: black;
}

Note

In CSS, the . character is not allowed in element ids; and the #states.foo selector matches the element with id states only if it also has the class foo. Since this form of identifier comes up so frequently in GeoServer layers, the CSS module deviates from standard CSS slightly in this regard. Future revisions may use some form of munging to avoid this deviation.

Filtering by rendering context (scale)

Often, there are aspects of a map that should change based on the context in which it is being viewed. For example, a road map might omit residential roads when being viewed at the state level, but feature them prominently at the neighborhood level. Details such as scale level are presented as pseudo-attributes; they look like property filters, but the property names start with an @ symbol:

[roadtype = 'Residential'][@sd > 100k] {
    stroke: black;
}

The context details that are provided are as follows:

Pseudo-Attribute Meaning
@sd The scale denominator for the current rendering. More explicitly, this is the ratio of real-world distance to screen/rendered distance.
@scale Same as above, the scale denominator (not scale) for the current rendering. Supported for backwards compatibility

The scale value can be expressed as a plain number, for for brevity and readability the suffixes k (kilo), M (mega), G (giga) can be used, for example:

[@sd > 100k]
[@sd < 12M]
[@sd < 1G]

Note

While property filters (currently) use the more complex ECQL syntax, pseudo-attributes cannot use complex expressions and MUST take the form of .

Filtering symbols

When using symbols to create graphics inline, you may want to apply some styling options to them. You can specify style attributes for built-in symbols by using a few special selectors:

PseudoSelector Meaning
:mark specifies that a rule applies to symbols used as point markers
:stroke specifies that a rule applies to symbols used as stroke patterns
:fill specifies that a rule applies to symbols used as fill patterns
:symbol specifies that a rule applies to any symbol, regardless of which context it is used in
:nth-mark(n) specifies that a rule applies to the symbol used for the nth stacked point marker on a feature.
:nth-stroke(n) specifies that a rule applies to the symbol used for the nth stacked stroke pattern on a feature.
:nth-fill(n) specifies that a rule applies to the symbol used for the nth stacked fill pattern on a feature.
:nth-symbol(n) specifies that a rule applies to the symbol used for the nth stacked symbol on a feature, regardless of which context it is used in.

For more discussion on using these selectors, see Styled marks.

Global rules

Sometimes it is useful to have a rule that matches all features, for example, to provide some default styling for your map (remember, by default nothing is rendered). This is accomplished using a single asterisk * in place of the usual filter. This catch-all rule can be used in complex expressions, which may be useful if you want a rule to provide defaults as well as overriding values for some features:

* {
    stroke: black;
}